View and Download AMMCO installation instructions manual online. Disc Rotor Lathe. Lathe pdf manual download. iv • AMMCO Brake Lathes. Safety. Safety Notices and. Decals. For your safety, and the safety of others, read and understand all of the safety notices and . Get AMMCO Disc Rotor Lathe Manual. Get all AMMCO manuals!.
|Published (Last):||27 April 2005|
|PDF File Size:||1.16 Mb|
|ePub File Size:||12.33 Mb|
|Price:||Free* [*Free Regsitration Required]|
Move the tool bits inward until they just contact the faces of the rotor. Retighten the arbor nut. Do this for your own protection. Repeat the procedure for the other tool-bit holder. Tell us what’s missing. After the brake rotor is mounted on the arbor, install the silencer band.
Any excessive wear or deformity should be noted and, if not within acceptable limits, the rotor should be replaced. Unplug unit from power source before servicing or adjusting. Reconditioning Disc Brake Rotors The patented self-aligning spacer prevents diagonal thrust on the adapters.
This is easily done by stretching the band to its full length and then wrapping it around the rotor and hooking the end metal loop over a lead weight, Fig.
Either rough or finish cuts may be taken to resurface a rotor. Also review the following general safety instructions. Proper maintenance and inspection is necessary for safe operation. Turn the left hand tool bit control until the tool bit contacts the rotor surface and makes a scratch cut no deeper than. Loosen the stud nut, Fig.
Now engage the automatic cross feed by moving the knobFig. READ these instr uctions bef ore placing unit in. Brake Lathes Arbor Installation The 1″ arbor shipped with the lathe has been carefully matched to the lathe during final assembly and testing.
Table of Contents Add to my manuals Add. To print the manual completely, please, download it. B 10, and adjust the twin cutter so that the rotor is centered between the tool bits.
AMMCO INSTALLATION INSTRUCTIONS MANUAL Pdf Download.
Or point us to the URL where the manual is located. Cutting or grinding on an exposed sur- face such as a rotor will produce flying chips.
Brake 700 Care of Arbors and Adapters CAUTION Although the adapters, arbors, and the spindle are smmco of top grade steel and are turned, hardened, and precision ground to close ammdo, great care should be taken in their use, handling, and storage.
Page 11 Brake Lathes Cross Feed – The cross feed draws the twin tool bits across the face of a brake rotor when the cross feed drive is engaged. Page of 20 Go. Page 15 Brake Lathes The scratch will usually appear as an incomplete circle. Comments to this Manuals Your Name. Safety Safety Notices and Decals For your safety, and the safety of others, read and understand all of the safety notices and decals a,mco here and on the unit.
Your manual failed to upload Failure to follow safety instructions could result in personal injury to operator or bystanders and damage to the lathe or personal property. Keep bystanders out of work area. Turn the outer knurl of the twin cutter control left and right to check for a smooth, free movement. The patented self-aligning spacer prevents diagonal thrust on the adapters.
Page 19 Brake Lathes Care of Arbors and Adapters CAUTION Although the adapters, arbors, and the spindle are made of top grade steel and are turned, hardened, and precision ground to close tolerances, great care should be taken in their use, handling, and storage.
Use a micrometer to check the thickness of the rotor at no less than three points around ammmco circumference akmco 1″ Adjust the drive belt to match the rotor size.
What’s missing? Tell us about it.
Brake Lathes Installation Receiving The shipment should be thoroughly inspected as soon as it is received. A true running arbor is essential to professional quality rotor reconditioning. Safety glasses, goggles, or a face shield contact persons in the area causing personal ammfo. Chips and dust could be driven between machined parts and into bearings causing undue wear. For additional copies of either, or further information, contact: Replace or repair damaged or worn cords immediately soon as it is received.
Warning This equipment incorporates parts such as snap switches and power receptacles which tend to produce arcs or sparks. Don’t show me this message again. Reconditioning Disc Brake Rotors-set-up Fig. Refill as necessary with EP gear oil and check the oil level often. Brake Lathes Machining 8. Oiling The lathe is shipped from the factory with the correct amount and type of oil.
AMMCO Hustler Disc Brake Lathe Operation Manual | eBay
Feed Speed – Feed speed refers to the number of thousandths of an inch the cutting tools move across the face of the rotor per revolution of the spindle. Spindle Speed – Release the belt tension by moving the V-belt adjusting lever clockwise, Fig. Brake 70000 Cross Feed – The cross feed draws the twin tool bits across the face of a brake rotor when the cross feed drive is engaged.
Center the twin cutter to the rotor. Make sure that the tool bits clear ammcco rotor faces and the silencer band. Important Safety Instructions Safety glasses, goggles, or a face shield contact persons in the area causing personal injury.